2008 kia sedona throttle position sensor

You search PDF repair manual about 2008 kia sedona throttle position sensor, if there are search results will appear below. If search results do not exist, please search by others keyword.



  2008 kia sedona throttle position sensor Direct Download speed 5432 Kb/s

  2008 kia sedona throttle position sensor Full Version speed 8172 Kb/s



Kia Sorento/ Sedona Throttle Position Sensor W/ 3.5L Engine (Fuel System) Service Procedure

0

Filed Under (Kia Motors Manuals) by admin on 11-01-2012

download
Replacement Procedure: 1. Turn ignition OFF. Remove engine cover and disconnect electrical connector from TP Sensor. 2. Remove two (2) retaining screws from TP Sensor and remove from throttle body. 3. Install new TP Sensor to throttle body. Install retaining screws and hand tighten lightly. Adjustment will be required. Re-install electrical connector to TP Sensor. 4. Install Global Diagnostic System. a. Select “System Option” b. Select “Idle RPM Adjust Mode” c. Apply Parking Brake 5. Select Neutral position and place engine in idle condition with A/C OFF. 6. Remove rubber plug and adjust using instructions provided on screen. Set Base idle between 800~900 rpm Adjust TPS: 7. Using the GDS scan tool, monitor current data using two (2) parameters: • Closed Throttle Position Switch • Throttle Position Voltage Value 8. Open throttle by hand very slowly until idle switch status switches to OFF. Note the TPS voltage value. Voltage:____________________________ 9. Close throttle and record the TPS voltage. oltage:____________________________ Closed throttle voltage should be 30~65mV less than the voltage noted in step eight (8). Adjust TP Sensor and repeat test as required. WARRANTY CLAIM INFORMATION: 10. Tighten TP Sensor screws as required. Torque is 12~18 inch lbs. Verify switching of throttle switch with throttle plate movement. 11. Install engine cover. 12. Clear any stored DTC which may have set during service procedure. Remove GDS tool from vehicle

Related Content:

how to adjust a cat forklift throttle position sensor, how to check 2006 G6 throttle sensor, kia sorento throttle position sensor, 2008 silverado replace tps, 2006 kia amanti idle speed adjustment, tps sensor 5 3l vortec, throttle body relearn for ford f150, Throttle body relearn for a ford f150, replaced throttle body new on my 2004 saturn vue and ligjt still comes on and off, replace throttle body sensor ford escape

1996 Ford Taurus Camshaft Position Sensor removal and installation manual

0

Filed Under (Ford Manuals) by admin on 16-06-2012

download
REMOVAL CAUTION: Prior to removal of the Camshaft Position (CMP) sensor, set cylinder No.1 to zero degrees Top Dead Center (TDC) of compression stroke. Then note the position of the CMP sensor electrical connector. The installation procedure requires that the connector be located in the same position. 1. Disconnect battery ground cable. NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the Powertrain Control Module (PCM) relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy. 2. Disconnect engine control sensor wiring connector from CMP sensor. 3. Remove retaining screws and CMP sensor from sensor housing. 4. If removing CMP sensor housing from the cylinder block, proceed with Removal Step 5. If not removing sensor housing, proceed to installation Step 6. 5. Remove hold-down clamp (bolt and washer assembly) . 6. Remove CMP sensor housing from cylinder block INSTALLATION CAUTION : A special service tool such as Syncro Positioning Tool T95T-12200-A must be obtained prior to installation of the replacement CMP sensor. Failure to follow this procedure will result in improper sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage. 1. Attach Syncro Positioning Tool T95T-12200-A as follows: a. Engage CMP sensor housing vane into the radial slot of the tool. b. Rotate tool on CMP sensor housing until tool boss engages notch in sensor housing. 2. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly. 3. Install sensor housing so that drive gear engagement occurs when arrow on ocator tool is pointed approximately 75 degrees counterclockwise from the rear face of the cylinder block. This step will locate CMP sensor electrical connector in the pre-removal position. 4. Rotate Syncro Positioning Tool T95T-12200-A clockwise slightly. This will engage oil pump intermediate shaft. Push downward while adjusting Syncro Positioning Tool T95T-12200-A until the Syncro Gear engages the camshaft gear. 5. When synchronizer flange is fully seated against block, the installation tool should be facing counterclockwise of engine centerline approximately 33 to 45 degrees. 6. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14- 22 lb ft)

Related Content:

2003 explorer impact sensor, howtoinstallnewairbagsenscoron2004chevy1500pickuptruck, how to change 2010 hhr cam sensor, cam timing sensor 2006 nissan frontier, 2007 toyota tundra camshaft position sensor removal, 2005 Tahoe Repair Manual PDF, Is there a resister on a 2008 ford 5 4 triton, 2005 chevy trailblazer camshaft position sensor install, 2004 nissan quest o2 sensor, how much to repair cam timing sensor in nissan frontier

1999 Jeep Grand Cherokee Limited AUTOMATIC TRANSMISSIONS Chrysler 45RFE Electronic Controls Repair Manual

0

Filed Under (Jeep Manuals) by admin on 11-07-2012

download
INTERNAL TCM Circuit Description The TCM is reporting internal errors. Diagnostic Procedure 1. Turn ignition switch to LOCK position. Remove transmission control relay. Measure resistance between ground and relay ground circuit (Black/Yellow wire) in relay connector. If resistance is greater than 5 ohms, repair open circuit. If resistance s not greater than 5 ohms, go to next step. 2. The TCM has an internal problem and must be replaced. P0715: INPUT SPEED SENSOR ERROR Circuit Description DTC P0715 will set if an excessive change in input RPM has been detected in any gear. Possible Causes * Intermittent wiring and connector problems. * Faulty input speed sensor. * Input speed sensor circuits shorted to ground, shorted to voltage, or open. * Faulty TCM. Diagnostic Procedure 1. Place gear selector in “P” position and start engine. Using scan tool, monitor input speed sensor value. If value is less than 400 RPM, go to next step. If value is not less than 400 RPM, go to step 9. 2. Turn ignition switch to LOCK position. Install Transmission Simulator (8333). Turn ignition on. Using transmission simulator, turn rotary knob to middle (1000/3000) position. Turn INPUT/OUTPUT switch on. Using scan tool, monitor input and output speed sensor values. If input speed sensor value is 2950- 3050 RPM and output speed sensor value is 950-1050 RPM, replace input speed sensor. If speed sensor values are not as specified, go to next step. 3. Turn ignition switch to LOCK position. Disconnect TCM harness connector. Remove transmission control relay. Using fused jumper wire, jumper fused B+ circuit (Red/White wire) and transmission relay output circuit (Red wire) together at relay connector. Turn ignition on. Measure voltage between ground and input speed sensor signal circuit (Red/Black wire) at TCM harness connector. If voltage is greater than 3 volts, repair circuit for short to voltage. If voltage is not greater than 3 volts, remove jumper wire, install relay and go to next step. 4. Turn ignition switch to LOCK position. Disconnect input speed sensor harness connector. Measure resistance of input speed sensor signal circuit (Red/Black wire) between TCM and input speed sensor. If resistance is greater than 5 ohms, repair open circuit. If resistance is not greater than 5 ohms, go to next step. 5. Measure resistance of input speed sensor ground circuit (Dark Blue/Black wire) between TCM and input

Related Content:

yhs-fh_lsonsw, kia rondo input speed sensor, How to remove back up sensor on 2012 explorer rear bumper, WHERE IS THE FUSE PANEL IN A 1986 TOYOTA PICKUP, where is the rpm sensor for a kia sedona, where is the transfer case speed sensor on a avalanche, asc spoiler sunroof wont close grand cherokee, nissan liberty gearbox, manual toyota lc200 pdf, replacing a input turbine speed sensor for 2004 mazda 3

GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps)

0

Filed Under (More Manuals) by admin on 03-02-2012

download
GM Accessories Headrest DVD System Display Monitor Inoperative (Install Cable Connector Clamps) Models: 2004-2007 Buick Rainier 2008 Buick Enclave 2003-2008 Cadillac Escalade Models 2005-2008 Cadillac CTS, SRX, STS 2006-2008 Cadillac DTS 2003-2008 Chevrolet Avalanche, Silverado, Suburban, Tahoe, TrailBlazer Models 2006-2008 Chevrolet Colorado 2007-2008 Chevrolet Equinox, HHR 2003-2008 GMC Envoy Models, Sierra, Yukon Models 2006-2008 GMC Canyon 2007-2008 GMC Acadia 2007-2008 Pontiac Torrent 2005-2008 HUMMER H2 2006-2008 HUMMER H3 2007-2008 Saturn OUTLOOK 2005-2008 Saab 9-7X This bulletin is being revised to update the models affected list. Please discard Corporate Bulletin Number 07-08-44-016 (Section 08 — Body & Accessories). Condition Some customers may comment on an inoperative display monitor or monitors in the GM Accessories Headrest DVD System. Cause This condition may be caused by a loose connection at the display monitor cable connectors. These connectors are located at the lower rear part of both front seats. Two cables are routed to the display monitor in each seat. Correction Do This Don’t Do This Install display monitor cable connector clamps. Do Not replace the DVD system display monitor. Important: A number of headrest monitors have been replaced under warranty and in many cases, no trouble was found by the supplier when these units were analyzed. Therefore, technicians should be checking for loose connections and installing cable connector clamps to ensure a positive and robust connection. Technicians are to install a video cable connector clamp on each cable connector located under each front seat. A total of four cable connector clamps, P/N 19159659, are required for each vehicle. The illustration above shows a pair of display monitor cable connectors without the cable clamps installed.

Related Content:

allinurl:Electronic Ignition Key , yhs-looksafe_ds_trans, how to change the thermostat 2008 ford escape ehow, 2008 SCION XB BRAKE ROTOR RELEASE TOOL, 2008 checrolet colorodo emmisions purge valve, 2008 pilot alternator replacement, FREE PDF DOWNLOAD OF 2008 SILVERADO Z71 REPAIR MAMUAL, indictor light on 2008 chevy sliverdo, 2008 ford fusion transmission sensor, ac drain on a 2008 silverado

Kia 2002 Saturn SL will set if TP sensor voltage is less than 0.2 volts

0

Filed Under (Kia Motors Manuals) by admin on 26-05-2011

download
The throttle position (TP) sensor is a potentiometer that varies resistance according to changes in throttle plate position. The powertrain control module (PCM) measures the signal voltage from the TP sensor which is a reduced value of the PCM 5-volt reference. The voltage ranges from 0.4 (+/-0.2) volts at 0% throttle position to 4.7 volts at wide open throttle. DTC P0122 sets when the TP sensor signal voltage at the PCM is below the calibrated voltage value. DTC Parameters DTC P0122 will set if TP sensor voltage is less than 0.2 volts when: z The condition exists for longer than 10 seconds. z The ignition is ON. DTC P0122 diagnostic runs continuously with ignition ON. DTC P0122 is a type A DTC. Diagnostic Aids Important If DTC P1635 is set, diagnose that DTC first. 2002 Saturn SL
To locate an intermittent problem, use a scan tool to monitor TP SENSOR voltage with ignition ON, engine OFF. Wiggling the wires while watching for a change in TP SENSOR voltage may locate the area where an open or short to ground in the wiring could lie. An intermittent open in the TP SENSOR can cause this DTC to set. Use the scan tool to monitor TP SENSOR as the accelerator pedal is slowly depressed. The voltage should change smoothly from 0.4 volts at 0% throttle, to 4.7 volts at wide open throttle (+/-0.2 volts).

1991-1992 Toyota MR2 Turbo 1990-1992 Toyota Celica All Trac ECU Pinout Diagram

0

Filed Under (Toyota Manuals) by admin on 18-04-2012

download
A13 Power Ground Chassis ground Ground A14 Power Ground Chassis ground Ground A20 Ignition Control Module Engine speed Speed A26 Power Ground Chassis ground Ground Connector B Pin # Name Function Signal Type B3 Intake Air Temperature Sensor Air temperature sensor signal Analog B4 Engine Coolant Temperature Sensor Engine coolant temperature sensor signal Analog B5 Knock Sensor Engine knock sensor Knock, Audio B6 Primary 02 Sensor Primary oxygen sensor signal Analog B11 Throttle Position Sensor Throttle position sensor signal Analog B13 MAP Sensor Manifold absolute pressure sensor signal Map min: 4.89 Map max: 1.09 Analog Connector D Pin # Name Function Signal Type D1 Voltage Back Up Permanent 12V Power D4 Brake Switch Brake switch signal Analog D9 Vehicle Speed Sensor Vehicle speed sensor signal Speed D12 Power Source 12V switched Power D13 Power Source 12V switched

Related Content:

change knock sensor 2005 chevy avalanche, diogram of knock sensor on 1999 lumina, where is the air temp sensor on 2001 toyota celica

1991-1992 Toyota MR2 Turbo, 1990-1992 Toyota Celica All Trac ECU Pinout Diagram

0

Filed Under (Toyota Manuals) by admin on 21-09-2011

download
Connector A Pin # Name Function Signal Type A13 Power Ground Chassis ground Ground A14 Power Ground Chassis ground Ground A20 Ignition Control Module Engine speed Speed A26 Power Ground Chassis ground Ground Connector B Pin # Name Function Signal Type B3 Intake Air Temperature Sensor Air temperature sensor signal Analog B4 Engine Coolant Temperature Sensor Engine coolant temperature sensor signal Analog B5 Knock Sensor Engine knock sensor Knock, Audio B6 Primary 02 Sensor Primary oxygen sensor signal Analog B11 Throttle Position Sensor Throttle position sensor signal Analog B13 MAP Sensor Manifold absolute pressure sensor signal Map min: 4.89 Map max: 1.09 Analog Connector D Pin # Name Function Signal Type D1 Voltage Back Up Permanent 12V Power D4 Brake Switch Brake switch signal Analog D9 Vehicle Speed Sensor Vehicle speed sensor signal Speed D12 Power Source 12V switched Power D13 Power Source 12V switched Power

1990-1994 Lexus LS400 How to Check Air Conditioning Diagnostic

0

Filed Under (Lexus Manuals) by admin on 15-06-2012

download
1) First perform an indicator check to see if all the lights are working properly. Press and hold the AUTO & REC buttons and then start the car. Release the buttons after the car has started. All the lights should light up and go off 4 times in a row at one second intervals. You should also hear a beep as the indicators light up. After the indicators blink 4 times you’re in A/C diagnostic mode. 2) Read the code displayed on the LCD. Here you see a code 21; this can happen if you’re not in light because it refers to the solar sensor. 3) Here’s what normal will look like, code 00. When the codes are displayed they blink and beep. Here are all the codes that can be displayed……… Code – Meaning 00 – Normal 11 – Open or short in room temperature sensor circuit. 12 – Open or short in ambient temperature sensor circuit. 13 – Open or short in evaporator temperature sensor circuit. 14 – Open or short in water temperature sensor circuit. 21* – Open or short in solar sensor circuit. 22* – Compressor motor locked. And/or, open or short in compressor lock sensor circuit. 31 – Open or short in air mix damper position sensor circuit. 32 – Open or short in air inlet damper position sensor circuit. 33 – Open in air mix damper position sensor circuit. Or, open or short in air mix servomotor circuit. Or, air mix servomotor locked. 34 – Open in air inlet damper position sensor circuit. Or, open or short in air inlet sensor servomotor circuit. Or, air inlet servomotor locked. * – These are detected only when they are the current troubles. Other codes detect both current trouble (beep) and past trouble (no beep). A/C indicator light blinks – This means your A/C compressor is locked. It’s happened to me before and I needed a new (rebuilt) compressor installed. 4) Once you’ve read any codes you can proceed to performing an actuator check by pressing the REC button. This will start a check of different combinations for the system starting with code 20 and moving up to 29. To cancel this or the previous diagnostic modes simply press the OFF button.

Related Content:

gm b0100 code short ind squib circurt, gmc acadia b0100 2008, injection actuation pressure sensor circuit

1996 Ford Taurus Service and Repair Manual

0

Filed Under (Ford Manuals) by admin on 01-02-2012

download
REMOVAL CAUTION: Prior to removal of the Camshaft Position (CMP) sensor, set cylinder No.1 to zero degrees Top Dead Center (TDC) of compression stroke. Then note the position of the CMP sensor electrical connector. The installation procedure requires that the connector be located in the same position. 1. Disconnect battery ground cable. NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the Powertrain Control Module (PCM) relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy. 2. Disconnect engine control sensor wiring connector from CMP sensor. 3. Remove retaining screws and CMP sensor from sensor housing. 4. If removing CMP sensor housing from the cylinder block, proceed with Removal Step 5. If not removing sensor housing, proceed to installation Step 6. 5. Remove hold-down clamp (bolt and washer assembly) . 6. Remove CMP sensor housing from cylinder block INSTALLATION CAUTION : A special service tool such as Syncro Positioning Tool T95T-12200-A must be obtained prior to installation of the replacement CMP sensor. Failure to follow this procedure will result in improper sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage. 1. Attach Syncro Positioning Tool T95T-12200-A as follows: a. Engage CMP sensor housing vane into the radial slot of the tool. b. Rotate tool on CMP sensor housing until tool boss engages notch in sensor housing. 2. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly. 3. Install sensor housing so that drive gear engagement occurs when arrow on

Related Content:

1996 ford taurus repair manual pdf free

2001 Mercedes-Benz SLK320 3.2L Engine light is on with no acceleration

0

Filed Under (Mercedes-benz Manuals) by admin on 22-01-2012

download
1. Connect scan tool and monitor voltages of pedal sensor B37. Signal 1 (Accelerator pedal position: Idle speed):[0.2...0.5] V Signal 2 (Accelerator pedal position: Idle speed):[0.1...0.5] V Signal 1 (Accelerator pedal position:Kickdown):[4.3...4.8] V Signal 2 (Accelerator pedal position:Kickdown):[2.1...2.5] V 2. If voltages are out of specification verify correct reference voltage to sensor by measuring between pins 6 (Black/White wire) and pin 1 (Blue/Grey wire) on pedal sensor connector. Voltage needs to be between 4.75 and 5.25 volts. 3. Test throttle body voltages with scan tool. Potentiometer #2 signal voltage ignition on, accelerator pedal position CTP 0.3-0.9 VDC, WOT > CTP value Potentiometer #1 signal voltage Ignition on, accelerator pedal position CTP 4.0-4.6 VDC, WOT < CTP value. 4. Test mass air flow sensor voltage. Sensor signal voltage must start KOEO around 1 volt and go up as engine RPMs increase. This can also be seen under air sensor volume output, output value must go up not down. Potential Causes: Pedal Sensor Throttle Body Wiring Tech Tips: With new sensor the throttle stops must be relearned. Use compatible scan tool and perform adaptations. ALWAYS verify charging system voltage is correc

Related Content:

engine compartment position diagram for 2001 mercedez benz slk320, peugeot 306 throttle

Related Content:

how to adjust a cat forklift throttle position sensor, how to check 2006 G6 throttle sensor, kia sorento throttle position sensor, 2008 silverado replace tps, 2006 kia amanti idle speed adjustment, tps sensor 5 3l vortec, throttle body relearn for ford f150, Throttle body relearn for a ford f150, replaced throttle body new on my 2004 saturn vue and ligjt still comes on and off, replace throttle body sensor ford escape