delphi 210 fip pump

You search PDF repair manual about delphi 210 fip pump, if there are search results will appear below. If search results do not exist, please search by others keyword.



  delphi 210 fip pump Direct Download speed 5432 Kb/s

  delphi 210 fip pump Full Version speed 8172 Kb/s



1993 Ford Escort CIRCUIT TEST J – FUEL PUMP CIRCUIT (RELAY AND INERTIA SWITCH)

0

Filed Under (Ford Manuals) by admin on 19-01-2012

download
resistance between test pin No. 22 and test pins No. 40 and 60. If resistance is less than 10,000 ohms, repair short circuit and repeat QUICK TEST. If resistance is 10,000 ohms or more, go to step 5). 5)Check Fuel Pump Circuit Continuity Turn ignition off. Leave fuel pump relay and PCM disconnected. Measure resistance between FUEL PUMP circuit at fuel pump relay wiring harness connector and test pin No. 22 at breakout box. If resistance is less than 5 ohms, replace PCM and repeat QUICK TEST. If resistance is 5 ohms or more, repair open circuit and repeat QUICK TEST. 10)Code 95/542 A KOEO Code 95/542 indicates one of the following conditions: Engine Starts: * Fuel pump secondary circuit shorted to power. * Fuel pump relay contacts always closed. * Open FPM circuit between PCM and junction to POWER-TO-PUMP circuit. * Left/front HO2S short to power (dual HO2S applications). * Faulty PCM. No Start: * IFS switch circuit open or not reset. * Open circuit in or between PCM and fuel pump. * Faulty ground connection at fuel pump. * Faulty fuel pump. If engine starts, go to step 11). If engine does not start, go to step 15). 11)Check Fuel Pump Operation Turn ignition on. Wait 5 seconds. Listen for fuel pump operation. If fuel pump is off, go to step 13). If fuel pump is on, go to step 12). 12)Check For Fuel Pump Relay Always Closed Turn ignition off. Disconnect fuel pump relay. Turn ignition on. If fuel pump is off with relay disconnected, replace fuel pump relay and repeat QUICK TEST. If fuel pump is on with relay disconnected, repair short to power in POWER-TO-PUMP or FPM circuit. (For models with relay block, also check fuel pump prime plug circuit). Repeat QUICK TEST. 13)Check Continuity Of Fuel Pump Monitor (FPM) Circuit Turn ignition off. Disconnect PCM 60-pin connector. Inspect and repair any damaged terminals. Install EEC-IV Breakout Box (T83L-50-EEC-IV) , leaving PCM disconnected. Disconnect fuel pump relay. Measure resistance between test pin No. 8 (No. 19 on Escort, and Tracer) at breakout box and POWER-TO-PUMP circuit at fuel pump relay wiring harness connector. If resistance is less than 5 ohms, go to step 25) (dual HO2S) or replace PCM and repeat QUICK TEST (single HO2S). If resistance is 5 ohms or more, repair open circuit and repeat QUICK TEST

Related Content:

99 subaru forester fuel line repair kits, bp44 repair manual pdf, toyota so5d engine fule pump control wireing diagram pdf, lucas cav injection pump diagram, CAV Fuel Injector Pump (Ford Part #D6NN9A543G) repair manual, 2002 isx cummins manual pump installation, how to change water pump on a dewoo, isuzu dmax fuel pump, cav injector pump governor spring, rager injection pump parts manual

1998 Acura 3.5RL FUEL PUMP RELAY (3.5RL) INSTALLATION MANUAL

0

Filed Under (Acura Manuals) by admin on 13-06-2011

download
Fuel pump relay is located in the front of the trunk. Turn ignition switch to START position. If engine starts, go to next step. If engine does not start, go to FUEL PUMP RESISTOR (3.5RL) . 2. Turn engine off and ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is present, go to next step. If battery voltage is not present, go to step 4). 3. Start engine and run at 3000 RPM with no loads and transmission in Park or Neutral, until radiator fan comes on. Allow engine to idle for at least one minute. Turn engine off. Disconnect vacuum hose No. 21 from vacuum manifold. Apply 8-12 in. Hg (27-40 kPa) vacuum to Manifold Absolute Pressure (MAP) sensor. Start engine and run at 6500 RPM with no loads and transmission in Park or Neutral. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If less than one volt is present, fuel pump relay circuit is okay. If one volt or more is present, substitute a known good PCM, then recheck. If symptom or indication goes away, replace original PCM. 4. Turn ignition off. Disconnect PCM 26-pin and 12-pin connectors. Disconnect fuel pump relay 4-pin connector. Using a fused jumper wire, connect fuel pump relay connector terminals No. 2 (Red/White wire) and No. 4 (Green wire). Turn ignition on. Measure voltage between ground and PCM 12-pin connector terminal No. 4 (Green wire). If battery voltage is not present, go to next step. If battery voltage is present, replace fuel pump relay. 5. Remove jumper wire. Measure voltage between ground and fuel pump relay 4-pin connector terminal No. 2 (Red/White wire). If battery voltage is present, repair open or short in Green wire between PCM and fuel pump relay. If battery voltage is not present, repair open in Red/White wire between fuel pump relay and FUEL PUMP fuse No. 22 (20-amp), located in underdash fuse/relay box. FUEL PUMP RESISTOR (3.5RL) 1. Fuel pump resistor is located in the left corner of the trunk. Disconnect fuel pump resistor 2-pin connector. Turn ignition on and measure voltage between ground and fuel pump resistor connector terminal No. 2 (Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, go to next step. If battery voltage is not present as specified, check PGM-FI relay. See PGM- FI MAIN RELAY . 2. Turn ignition off. Using a jumper wire, connect fuel pump resistor connector terminals No. 1 (Black/Yellow wire) and No. 2 (Yellow wire). Turn ignition switch to START position. If engine does not start, go to next step. If engine starts, replace fuel pump resistor. 3. Turn ignition off. Disconnect fuel unit sub-harness Gray, 10-pin connector located in front of trunk, above fuel pump access panel, next to Gray, 20-pin connector. Turn ignition on and measure voltage between ground and sub-harness connector terminal No. 7 (Black/Yellow wire) within 2 seconds. If battery voltage is present for 2 seconds after ignition is turned on, check fuel pump. If battery voltage is present as specified, repair open in Black/Yellow wire between fuel pump resistor and fuel pump

Related Content:

wire diagram on a 2002 grand prix headlight, 1998 jimmy fuel pump install, 03 ford windstar fuel pump wiring, 86 corvette wiring schematics, damaged fuel pump wiring, proper connection for horn relay 1968 chevelle, 2005 tundra speed pulse signal wire location, location of vent valve solenoid on 2010 ford ranger, pontiac grand am fuel pump wireing harness replacement instructions, vcm ground wire

1998 Dodge Grand Caravan Fuel Pump Relay Removal And Installation Manual

0

Filed Under (Dodge Manuals) by admin on 13-06-2012

download
Fuel Pump Relay 1. Remove fuel pump relay from power distribution center at driver’s side front corner of engine compartment, near the battery. Note terminal identification on fuel pump relay. See Fig. 6 . 2. To check fuel pump relay resistance, use ohmmeter and check resistance between terminals No. 85 and 86 on fuel pump relay. Replace fuel pump relay if resistance is not 70-80 ohms. 3. To check fuel pump relay operation, connect ohmmeter between terminals No. 30 and 87A on fuel pump relay. See Fig. 6 . Ohmmeter should indicate continuity between terminals No. 30 and 87A on fuel pump relay. 4. Connect ohmmeter between terminals No. 30 and 87 on fuel pump relay. See Fig. 6 . Ohmmeter should indicate no continuity between terminals No. 30 and 87 on fuel pump relay. 5. Connect 16-gauge jumper wire between negative battery terminal and terminal No. 85 on fuel pump relay. Connect 16-gauge jumper wire between positive battery terminal and terminal No. 86 on fuel pump relay. 6. Fuel pump relay should now be energized. No continuity should now exist between terminals No. 30 and 87A on fuel pump relay. Continuity should now exist between terminals No. 30 and 87 on fuel pump relay. Disconnect jumper wires. Replace fuel pump relay if defective. 7. If fuel pump relay or wiring circuit failure exists, a Diagnostic Trouble Code (DTC) will be stored in Powertrain Control Module (PCM). See appropriate G – TESTS W/CODES article. Fig. 6: Identifying ASD Relay & Fuel Pump Relay Terminals Courtesy of CHRYSLER CORP.

Related Content:

yhs-default, fuse for right headlight eclipse 2000, which is the fuel pump relay on 2011 durango, location of fan relay 98 trans am, sensor switch on rear beam axle of 2005 saturn relay, 99 eldorado fuel pump relay test, where is the relay switch for liftgate in 2005 esclade, where is the washer relay located in a 2009 chevy impala, 1993 corvette power seat and power window shorting out breaker, g5 sunroof relay

1997-2001 HONDA CR-V (4WD) Noise From the Rear Differential REPAIR PROCEDURE

0

Filed Under (Honda Manuals) by admin on 06-01-2012

download
REPAIR PROCEDURE 1. Drain and refill the rear differential with Dual Pump Fluid. 2. Check the tires for proper inflation (recommended cold inflation front and rear is 26 psi) and any variation in tire size or type. 3. Test-drive the vehicle in a parking lot. Make tight, low-speed turns. If the noise is eliminated, return the vehicle to the customer. If the noise is still present, go to step 4. 4. Remove the rear differential assembly (see page 15-16 of the 1997-01 CR-V Service Manual). 5. Remove the torque control differential case, then remove and discard the 30 mm shim and the clutch assembly (see steps 1 thru 10 on pages 15-20 thru 15-22 of the service manual). 6. Remove the thrust needle bearing, the oil pump driveshaft, and the oil pump body assembly (see steps 11 and 12 on page 15-22 of the service manual). 7. Install the new flow collar over the drive pinion shaft. Make sure the tabs of the flow collar align with the oil pump pin. 8. For 1997 models: Assemble the new oil pump (spring, O-rings, piston, and pump body assembly). 9. Align the rear oil pump grooves with the oil pump pin and the flow collar tabs, then install the oil pump body assembly on the differential carrier. 10. Tighten the oil pump body assembly bolts to 12 N·m (8.7 lb-ft). 11. Align the oil pump driveshaft tabs with the grooves of the front oil pump in the oil pump body assembly, then install the oil pump driveshaft. 12. Install the thrust needle bearing with the outer race facing up.

Related Content:

differential service procedures, 2006 suburban oil pump replcement procedure, picture of 1997 4x4 honda passport axle warning lights, 1997 dodge ram 4x4 1500 service manual download, oil pump leak 2003 accord, oil pump on a 307, oil punp removal 2002 trailblazer, rav4 rear oil leak, Toyota 4 Y oil pump, what causes 147 transaxle code on 97 e420 mercedes

1997 Saturn SL2 OIL PUMP REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Saturn Manuals) by admin on 03-06-2012

download
Removal & Disassembly Remove engine front cover. See FRONT COVER & TIMING CHAIN under REMOVAL & INSTALLATION. Using an impact driver and a T-30 Torx bit, remove and discard oil pump cover plate screws. Remove cover plate and rotors. See Fig. 11 . To remove oil pump relief valve, use a slide hammer and Relief Valve Puller Adapter (SA9103E). Inspection Replace rotors if worn or damaged. Using feeler gauge and straightedge (at cover plate), measure oil pump clearances. See OIL PUMP SPECIFICATIONS table. If clearances are not as specified, replace rotors or entire pump assembly as necessary. Reassembly & Installation Install rotors with chamfer facing away from engine. Install new relief valve (if removed). Pack pump rotors with petroleum jelly to prime pump. Install pump cover plate using new screws. Tighten screws to specification. See TORQUE SPECIFICATIONS . OIL PUMP SPECIFICATIONS NOTE: If oil pump relief valve is removed, DO NOT reuse it. Application In. (mm) Outer Rotor-To-Housing .006-.011 (.150-.277) Outer Rotor Tip-To-Inner Rotor Tip .006 (.150) Rotor Gear-To-Pump Cover Plate

Related Content:

01 saturn dtc p1635

2002 BMW 325I 2.5L Air Pump Repair manual

0

Filed Under (Bmw Manuals) by admin on 05-02-2012

download
Check engine light on and fault codes stored. Vehicle running normally. Tests/Procedures: 1. Based upon stored fault codes for secondary air system, there is little or no flow of secondary air into engine. Typical causes for this issue are failed secondary air pumps and/or secondary air check valves. Secondary air pump should operate under normal circumstances when vehicle is first started to perform system test. Pump will normally be heard running when standing in front right corner of vehicle. 2. The secondary air pump is located in the right front of engine compartment. A secondary air pump relay located in the glove box is controlled by the engine control module and sends power to the secondary air pump. 3. Air pump can be disconnected and supplied with power and ground at pump to verify operation is possible. 4. Check valve on front right of cylinder head can be supplied with vacuum and visually checked for opening of valve. 5. Vacuum line from check valve to operating solenoid should also be inspected for cracks or being disconnected. Vacuum line follows right side of cylinder head to back of cylinder head to the secondary air solenoid located under left rear side of intake manifold. 6. The solenoid should allow vacuum flow to the check valve during vacuum pump operation. The solenoid is controlled directly by the engine control module and receives power during key-on-engine-off. Potential Causes: A.I.R. Check Valve Engine Control Module (ECM) Codes — Engine control module fault. Defective Secondary Air Pump Secondary Air Pump Relay Secondary Air Supply Hose Broken Vacuum Line

Related Content:

where is the secondary air pump located a 2002 rendezvouz, 2008 trailblazer air pump install, how to test a secondary air check valve on a 2002 bmw 325i, where is the air pump on a 2002 rendezvouz, where should a check valve be located

2004 Mazda 6 i Engine Mechanical WATER PUMP DRIVE BELT

0

Filed Under (Mazda Manuals) by admin on 09-06-2011

download
1. Verify that the water pump drive belt auto tensioner indicator mark does not exceeds the limit. ? If it exceeds the limit, replace the water pump drive belt. (See WATER PUMP DRIVE BELT .) Fig. 20: Water Pump Drive Belt Auto Tensioner Limit Indicator Mark – Normal WATER PUMP DRIVE BELT 1. Remove the plug hole plate. 2. Rotate the water pump drive belt auto tensioner counterclockwise to release the drive belt tension and remove the water pump drive belt. 3. Reinstall the water pump drive belt or install a new water pump drive belt. WATER PUMP DRIVE BELT PULLEY REMOVAL NOTE 1. Replace part A of the SST [303-009 (49 UN30 3009)] with the SST [303-457 (49 UN30 3457)].

Related Content:

2004 dodge neon water pump installation, 2004 dodge neon waterpump replacement directions, 2004 envoy water pump replacement, how to replace a water pump on 2004 dodge neon, replace water pump on 2004 Kia reo, replacing a water pump 2004 v=6 mazda, water pump 2004 neon

1995 Nissan-Datsun Maxim Water Pump Service and Repair REMOVAL AND INSTALLATION

0

Filed Under (Nissan Manuals) by admin on 03-06-2011

download
1.Drain coolant from drain plugs on radiator and both sides of cylinder block. 2.Remove drain plug on cylinder block. 3.Remove right side engine mounting, mounting bracket and nuts. 4.Remove drive belts and idler pulley bracket. 5.Remove chain tensioner cover and water pump cover. 6.Pushing timing chain tensioner sleeve, apply a stopper pin so it does not return. Then remove the chain tensioner assembly. 7.Remove the 3 water pump fixing bolts. Secure a gap between water pump gear and timing chain, by turning crankshaft pulley 2O° backwards. 8.Put M8 bolts to two M8-threaded holes out of 3 water pump fixing bolt holes 9.Tighten M8 bolts by turning half turn alternately until they reach timing chain rear case. In order to prevent damages to water pump or timing chain rear case, do not tighten one bolt continuously. Always turn each bolt half turn each time. 10.Lift up water pump and remove it. When lifting up water pump, do not allow water pump gear to hit timing chain. INSPECTION 1.Check for badly rusted or corroded body assembly. 2.Check for rough operation due to excessive end play. INSTALLATION 1.Before installing, remove all traces of liquid gasket from mating surface of water pump cover and chain tensioner cover using a scraper. Also remove traces of liquid gasket from mating surface of front cover. 2.Apply a continuous bead of liquid gasket to mating surface of chain tensioner cover and water pump cover. 3.Return the crankshaft pulley to its original position by turning it 2O° forward. 4.Install timing chain tensioner, then remove the stopper pin After installing the tensioner, race the engine at about 3,000 rpm under no load to purge air from the high-pressure chamber. The engine may produce a rattling noise. This indicates that air still remains in the chamber and is not a matter of concern. 5.Install drain plug on cylinder block. 6.Reinstall any parts removed in reverse order of removal

1997 Jeep Cherokee 2WD Serpentine Belt INSPECTION ADJUSTMENT REMOVAL And INSTALLATION

0

Filed Under (Jeep Manuals) by admin on 05-01-2012

download
INSPECTION When inspecting serpentine drive belts, small cracks that run across the ribbed surface of the belt from rib to rib are considered normal. If the the cracks are running along the rib (rather across), this is not normal and the belt(s) must be replaced. ADJUSTMENT It is not necessary to adjust belt tension on the 5.2L or 5.9L engines and on the 2.5L and 4.0L engines (without power steering). These engines are equipped with an automatic tensioner. The tensioner maintains correct tension at all times. 2.5L and 4.0L Engines With Power Steering See Figures 1, 2, 3 and 4 If the vehicle is not equipped with power steering, it will be equipped with an idler pulley. If equipped with an idler pulley, refer to and follow the 5.2L/5.9L belt removal and installation procedure. Loosen the pump upper pivot bolt, lower locknut and pump adjusting bolt using a ratchet and 13mm socket or a 13mm box wrench. 1. Use a belt tension gauge placed in the middle of the belt being tested. Proper tension for a new belt is 180-200 lbs. (800-900 N) and 140-160 lbs. (623-712 N) for a used belt. 2. Tighten the pump adjusting bolt to achieve proper tension and recheck the belt tension. 3. Fig. Fig. 1: Loosen the pivot bolt (1), then the locking bolt (2) to loosen the power steering pump from behind Fig. Fig. 2: Use a ratchet and 13mm size socket to rotate the power steering pump Fig. Fig. 3: Adjustment points on the 2.5L engines without power steering (rear view) Fig. Fig. 4: Adjustment points on the 2.5L engine (front view) Removal & Installation 2.5L and 4.0L Engines With Power Steering See Figures 5, 6 and 7 Fig. Fig. 5: Proper belt routing diagram can usually be found on a sticker located in the engine compartment Fig. Fig. 6: Common 4.0L engine serpentine belt routing Fig. Fig. 7: Common 2.5L engine serpentine belt routing Loosen the rear power steering pump mounting bolts using a ratchet and 13mm socket or a 13mm box wrench. 1. Loosen the pump upper pivot bolt, lower locknut and the pump adjusting bolt using a ratchet and 13mm socket or a 13mm box wrench. 2. Remove the belt. 3. To install: Install the belt. 4. Tighten the pump adjusting bolt to achieve proper tension. 5. Install the pump rear mounting bolts, pivot bolt and locknut. Tighten the bolts to 20. ft. lbs. (27 Nm). 6. Check the belt for proper tension. If tension is incorrect, refer to the adjustment procedure in this section. 7. 5.2L and 5.9L Engines See Figures 8, 9 and 10

Related Content:

1986 jeep cherokee serpentine belt route, serpintin belt diagram for 2006 jetta, kia 3 5 crank bolt for sale, jetta 2006 fan belt totation, GM 10 Bolt Rebuild Manual, gm 10 bolt instructions, 99 Jeep Cherokee Owners Manual pdf, 2010 Kia Forte Serpentine Routing Belt Diagram, 2004 honda civic serpentine belt, 1995 Jeep 2 5L ccv orfice and emissions

Ford 455C 555C 655C Tractor Loader Backhoe Service Manual

0

Filed Under (Ford Manuals) by admin on 23-05-2012

download
Engine Systems Chapter 1 3-Cylinder Diesel Engine 3-Cylinder Diesel Engine – Description and Operation 3-Cylinder Diesel Engine – Overhaul Chapter 2 4-Cylinder Diesel Engine 4-Cylinder Diesel Engine – Description and Operation 4-Cylinder Diesel Engine – Overhaul Chapter 3 Cooling System Cooling System – 3-Cylinder Engine Description and Operation Cooling System – 4-Cylinder Engine Description and Operation Cooling System – Overhaul Chapter 4 Troubleshooting, Specifications and Special Tools Troubleshooting Specifications Special Tools Part 2 Fuel Systems Chapter 1 Fuel System – General Fuel System – Description and Operation Fuel System – Adjustments DPA Distributor Type Fuel Injection Pump Fuel System – Adjustments DPS Distributor Type Fuel Injection Pump Fuel System – Fuel Tanks, Filters and Fuel Lines Overhaul Chapter 2 Fuel Injection Pump – DPA Distributor Type Fuel Injection Pomp – Description and Operation Fuel Injection Pump – Overhaul Fuel Injection Pump – ISO Test Conditions Fuel Injection Pump – Test Procedures Chapter 3 Fuel Injection Pump – DPS Distributor Type Fuel Injection Pump – Description and Operation Fuel Injection Pump – Overhaul Fuel Injection Pump – ISO Test Conditions Fuel Injection Pump – Test Procedure Chapter 4 Injectors Ford 455C Injectors – Description and Operation Injectors – Overhaul Chapter 5 Injectors Ford 555C and 655C Injectors – Description and Operation Injectors – Overhaul Chapter 6 Air Cleaners Dry Type Air Cleaner – Description and Operation Dry Type Air Cleaner – Overhaul Chapter 7 Turbocharger Turbocharger – Description and Operation Turbocharger – Overhaul Chapter 8 Troubleshooting, Specifications, Test Plans and Special Tools Troubleshooting – Diesel Engines Troubleshooting – Turbocharger Specifications Special Tools Test Plans Part 3 Electrical System Chapter 1 Wiring, Lights and Controls Wiring, Lights and Controls – Description and Operation Wiring, Lights and Controls – Fault Finding and Repair Circuit Diagrams and Wiring Harness Chapter 2 Battery
Battery – Description and Operation Battery – Maintenance and Tests Chapter 3 Starting System Starting System – Description and Operation Starting Motor – Overhaul Chapter 4 Charging System – A127 55 Amp Alternator with Integral Regulator Charging System – A127 55 Amp Alternator with Integral Regulator – Description and Operation Charging System – A127 55 Amp Alternator with Integral Regulator – Service Precautions, Preliminary Checks, Initial Tests and Alternator Component Tests Charging System – A127 55 Amp Alternator with Integral Regulator – Overhaul Chapter 5 Troubleshooting, Specifications and Special Tools Troubleshooting Specifications Special Tools Part 4 Power Reversing Transmission Chapter 1 4×4 Fully Synchronized Power Reversing Transmission Power Reversing Transmission – Description and Operation Introduction to Overhauling the Transmission Gear Shift Lever, Modulator Unit and Solenoid Control Valve – Overhaul Front End Overhaul Complete Overhaul Component Overhaul Chapter 2 8X8 Fully Synchronized Power Reversing Transmission Power Reversing Transmission – Description and Operation Introduction to Overhauling the Transmission Gear Shift Lever, Modulator Unit, Lockup Valves and Solenoid Control Valve – Overhaul Front End Overhaul Complete Overhaul Component Overhaul

Related Content:

MERCEDES BENZ KE JETRONIC FUEL SYSTEM TROUBLE TRACER, ford 550 backhoe operator manual, procedure for overhauling a gear pump, dpa injector pump govenor spring settings, ford 555c alternator wiring diagram, Lucas feul injector pump type 908 for tractor, how to repair fuel injectors on 2003 GMC Envoy, n14 cummins troubleshooting, j-38791 moore, mack 2001 fuel system

Related Content:

99 subaru forester fuel line repair kits, bp44 repair manual pdf, toyota so5d engine fule pump control wireing diagram pdf, lucas cav injection pump diagram, CAV Fuel Injector Pump (Ford Part #D6NN9A543G) repair manual, 2002 isx cummins manual pump installation, how to change water pump on a dewoo, isuzu dmax fuel pump, cav injector pump governor spring, rager injection pump parts manual