toyota hilux oil pressure regulator relief

You search PDF repair manual about toyota hilux oil pressure regulator relief, if there are search results will appear below. If search results do not exist, please search by others keyword.



  toyota hilux oil pressure regulator relief Direct Download speed 5432 Kb/s

  toyota hilux oil pressure regulator relief Full Version speed 8172 Kb/s



2003 Kia Optima L4-2.4L Timing Belt Service and Repair Manual

0

Filed Under (Kia Motors Manuals) by admin on 16-07-2012

download
3.Turn the crankshaft clockwise and align the timing marks so as to bring the No.1 cylinder to compression top-dead-center position. At this time the timing marks of the camshaft sprocket and the upper surface of the rocker cover should coincide, and the dowel pin of the camshaft sprocket should be at the upper side. Remove the auto tensioner. CAUTION: Rotate the crankshaft clockwise. 4.Remove the timing belt. NOTE: If the timing belt is reused, make an arrow mark indicating the turning direction (or the front of the engine) to make sure that the belt is reinstalled in the same direction as before 6.When the oil pump sprocket nut is removed, first remove the plug at left side of the cylinder block and insert a screwdriver to check the left counter balance shaft in position. Screwdriver used for this purpose should have a shaft 8 mm (0.3 inch) in diameter which can be inserted more than 60 mm (2.36 inch) 7.Remove the oil pump sprocket retaining nut and remove the oil pump sprocket. 8.Loosen the right counter balance shaft sprocket mounting bolt until it can be loosened by hand. 9.Next, remove tensioner “B” and remove timing belt “B”. CAUTION: After timing belt “B” has been removed, do not attempt to loosen bolt while holding sprocket with pliers, etc. 10.Remove the crankshaft sprocket “B” from crankshaft. INSPECTION Sprockets, Tensioner Pulley, and Idler Pulley 1.Check the camshaft sprocket, crankshaft sprocket, tensioner pulley, and idler pulley for abnormal wear, cracks, or damage. Replace as necessary. 2.Inspect the tensioner pulley and the idler pulley for easy and smooth pulley rotation and check for play or noise. Replace as necessary. 3.Replace if there is grease leak

Related Content:

pto connection on 2002 f450, kia transmission fuild temperture sensor, ford 555b engine oil capacity, park pin in a 4l60e transmission, mercury cougar beeping noise in idle, kia sedona 2004 repair manual pdf torrent, kia p0750 p0755 p0765, kancil manifold supply air inlet, instructions on radio for 2004 kia sorento, 1986 190e 2 3 throttle linkage adjustment

2003 GMC Truck C 1500 P/U 2WD Engine Knocking or Lifter Noise

0

Filed Under (GMC Manuals) by admin on 30-06-2012

download
Engine Lubrication: All Technical Service Bulletins Engine – Knocking or Lifter Noise File In Section: 06 – Engine/Propulsion System Bulletin No.: 02-06-01-038 Date: December, 2002 TECHNICAL Subject: Engine Knock or Lifter Noise (Replace 0-Ring) Models: 2001-2002 Chevrolet Camaro 2001-2003 Chevrolet Corvette 2001-2002 Pontiac Firebird 2002-2003 Cadillac Escalade, Escalade EXT 2000-2003 Chevrolet Suburban, Tahoe 2001-2003 Chevrolet Silverado 2002-2003 Chevrolet Avalanche 2000-2003 GMC Yukon, Yukon XL 2001-2003 GMC Sierra with 4.8L, 5.3L, 5.7L or 6.0L V8 Engine (VINs V, T, Z, G, S, N, U – RPOs LR4, LM7, L59, LS1, LS6, LQ9, LQ4) Condition Some customers may comment on an engine tick noise. The distinguishing characteristic of this condition is that it likely will have been present since new, and is typically noticed within the first 161-322 km (100-200 mi). The noise may often be diagnosed as a collapsed lifter . Additionally, the noise may be present at cold start and appear to diminish and then return as the engine warms to operating temperature. This noise is different from other noises that may begin to occur at 3219-4828 km (2000-3000 mi). Cause The 0-ring seal between the oil pump screen and the oil pump may be cut, causing aeration of the oil. Correction

Related Content:

2003 mitsubishi lancer es repair manual, 2003 chevrolet suburban ac evaporator, evap in 2003 chevy s10 pickup, 2003 pontiac vibe repair manual, front end diagram for a gmc 03 envoy, 2003 ford motorhome chassis repair manual, fuse diagram for 2003 impalaq, GMC Sierra 2003 Manual, engine replacement procedure 2003 honda odyssey, 2002 chevrolet silverado 2500hd manual

2005-2006 (LX) Chrysler 300/ Magnum/ Charger/ Pacifica Multiple Cylinder Misfire Or Rough Idle Repair Manual

0

Filed Under (Chrysler Manuals) by admin on 01-06-2012

download
REPAIR PROCEDURE: VALVE ROTATION: 1. Relieve the fuel pressure. Refer to the detailed service information available in TechCONNECTunder: Service Info>14-Fuel System>Fuel Delivery >Standard Procedure>Fuel System Pressure Release Procedure. 2. Remove upper intake manifold. Refer to the detailed service information available in TechCONNECTunder: Service Info >9-Engine>Manifolds>Intake Manifold> Removal. 3. Remove cylinder head cover(s). Refer to the detailed service information available in TechCONNECTunder: Service Info >9-Engine>Cylinder Head>Cylinder Head Cover(s) >Removal. 4. Remove rocker arm and shaft assembly. Refer to the detailed service information available in TechCONNECT under: Service Info >9-Engine>Cylinder Head> Rocker Arm/Adjuster Assembly >Removal). 5. Clean and mark the tip of each exhaust valve stem at the 12 O’clock position witha paint marker. The paint mark will be used later to assist with determining the amount of valve rotation. 6. Remove the sparkplugs. 7. Rotate the crankshaft clockwise, until the number 1 piston is at Top Dead Center (TDC) on the compression stroke. 8. Install the compression tester sparkplug adapter in cylinder#1 sparkplug hole. With air hose attached to sparkplug adapter, apply 620.5 to 689 kPa (90 to 100 psi) air pressure. This is to hold valves into place while servicing components. 9. Using Tool MD 998772A (1) with adapter 6527 (4) or equivalent, slightly compress the exhaust valve spring to release tension against the valve and valve spring retainer ( Fig. 1 ). 10. Remove the valve spring retainer locks and discard the locks. NOTE: It is important that the valve rotation section of this repair procedure be performed.

Related Content:

2005 pacifica repair manual, 2006 chrysler 300 misfire, replace main thermostat chrysler 300 06 2 7

FORD F450-F550 Aries PARTS AND SERVICE MANUAL

0

Filed Under (Ford Manuals) by admin on 22-05-2012

download
1. Find a suitable road crossing to position the vehicle on rail. If necessary set up cautionary devices to ensure safety. 2. Position the vehicle with the road wheel tires on the rails, and the rail wheel flanges positioned centrally above the railhead. Backing into position is usually easier. 3. Put the vehicle’s transmission into park or neutral. Set the parking brake. 4. Engage the PTO hydraulic pump or start the auxiliary hydraulic power source. 5. The rear will be placed on rail first. a. Raise the rail gear up a bit to relieve the pressure on the lock hook. b. Pull the T-handle for the lock to swing the hook out of the way. c. Lower the rail gear into position on the rail. d. Release the T-handle for the lock. 6. Check the alignment of the front rail wheels with the track – it might be necessary to adjust the position of the vehicle. 7. The front rail gear will now be lowered. a. Raise the rail gear up a bit to relieve the pressure on the pin lock. b. Remove the both pins from the upper holes. c. Lower the rail gear. d. Install the lock pins in the lower holes. 8. Engage the steering lock. 9. Drive the vehicle forward and backward a few yards to check vehicle’s operation and brakes. 10. Vehicle is now ready for rail travel. Removal of Vehicle from Rail 1. Find a suitable road crossing to remove the vehicle from the rail. 2. Put the vehicle’s transmission into park or neutral. Set the parking brake. 3. Engage the PTO hydraulic pump or start the auxiliary hydraulic power source. 4. The front will be raised first. a. Bump the rail gear down a bit to relieve the pressure on the lock pins. b. Remove both pins from the lower holes. c. Raise the rail gear into the road position. d. Insert the lock pins into the upper locking holes. 5. The rear will now be raised. a. Raise the rail gear b. The hook lock will automatically swing out of the way of the raising rail gear and swing into locking position. 6. Disengage the PTO hydraulic pump or auxiliary hydraulic power source. 7. Disengage the steering lock. 8. The vehicle is now ready to be driven on the road.

1995 Isuzu Trooper LS TIMING BELT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Isuzu Manuals) by admin on 13-05-2012

download
TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts. 2. Remove fan pulley assembly. Remove crankshaft pulley bolt. Using Puller (J-8614-01) or equivalent, remove crankshaft pulley. Remove oil cooler hose from timing cover. Remove timing belt cover. Align all timing marks prior to belt removal. See Fig. 1 – Fig. 4 . Remove belt tensioner pusher and timing belt. Fig. 1: Aligning Timing Belt Sprockets (DOHC) Courtesy of ISUZU MOTOR CO. Installation 1. Ensure all timing marks are aligned. Install belt over one pulley at a time starting at crankshaft sprocket and working counterclockwise. Belt should go over tensioner last. Secure belt at each pulley during installation with pinch clips. See Fig. 5 . 2. Compress timing belt tensioner pusher and insert pin to retain pusher. Apply pressure to tensioner against belt, and install tensioner pusher. Tighten bolts to specification. See TORQUE SPECIFICATIONS . 3. Loosen tensioner pulley bolt. Apply pressure on belt by rotating tensioner. Tighten tensioner pulley bolt to specification.. See TORQUE SPECIFICATIONS . Remove pin from timing belt tensioner pusher. 4. Remove pinch clips from timing belt (if used). Install crankshaft pulley, tightening center bolt finger tight. Rotate crankshaft 2 turns clockwise. Ensure timing belt tensioner pusher rod protrudes proper

Related Content:

2004 Isuzu NPR refrigerant, isuzu 4hk1 timing marks

2007-2009 Toyota FJ Cruiser Banks Monster Exhaust System Installation Manual

0

Filed Under (Toyota Manuals) by admin on 06-04-2012

download
1. Before starting work, familiarize yourself with the installation procedure by reading all of the instructions. 2. The exploded view (Figure 2) provides only general guidance. Refer to each step and section diagram in this manual for proper instruction. 3. Throughout this manual, the left side of the vehicle refers to the driver’s side, and the right side to the passenger’s side. 4. Disconnect the negative (ground) cable from the battery (or batteries, if there are two) before beginning work. 5. Route and tie wires and hoses a minimum of 6″ away from exhaust heat, moving parts and sharp edges. clearance of 8″ or more is recommended where possible. 6. When raising the vehicle, support it on properly weight-rated safety stands, ramps or a commercial hoist. Follow the manufacturer’s safety precautions. Take care to balance the vehicle to prevent it from slipping or falling. When using ramps, be sure the front wheels are centered squarely on the topsides; put the transmission in park; set the hand brake; and place blocks behind the rear wheels. Caution! Do not use floor jacks to support the vehicle while working under it. Do not raise the vehicle onto concrete blocks, masonry or any other item not intended specifically for this use. 7. During installation, keep the work area clean. Do not allow anything to be dropped into intake, exhaust, or lubrication system components while performing the installation, as foreign objects will cause immediate engine damage upon start-up. Tools Required: • 1? 2 ” and 3? 8 ” drive ratchets with standard and metric sockets and 1 ? 2 ” and 3? 8 ” drive extension • Standard and metric combination or open-end wrenches • Standard screwdriver • Clean shop towels or rags • Pry-bar Highly recommended tools and supplies: • Foot-pound torque wrench • Penetrating oil or light lubricant spray General Installation Practices 97083 v.2.0 3 Monster Exhaust SySTEM INSTallaTIoN 1. Disconnect the negative (ground) cable from the battery (if there is more than one battery, disconnect both negative cables). Secure the cable so it cannot accidentally come in contact with the post. 2. Raise the vehicle and support it securely with properly weight-rated safety stands, ramps or a commercial hoist. Take care to balance the vehicle to prevent it from slipping or falling. When using ramps, be sure the wheels are centered squarely on the topsides. Place the transmission in park (automatic), set the parking brake and securely block the wheels that are on the ground. CaUTIoN: Do NoT WoRK UNDER aNy VEHIClE SUPPoRTED oNly By a JaCK. SEVERE INJURy May RESUlT. 3. From under the vehicle remove the factory exhaust starting at the 2-bolt flange in front of the muffler. Remove the two (2) bolts, two (2) washers, and two (2) springs from the flange and retain for re-use. NOTE: Remove the factory gasket from the 2-bolt flange. The exhaust system will be hanging by the exhaust hanger pins. 4. Liberally apply an aerosol lubricant on all the hanger pins. Remove the exhaust system from the vehicle by removing each hanger pin from the rubber grommet. NOTE: Remove hanger pins from the front of the vehicle to the rear. 5. Drop the exhaust system to the floor and move out of the way. You will not be reusing any components from the exhaust system. 6. Install the Banks conical gasket onto the vehicle’s 2-bolt flange. 7. Install the hanger pin on the intermediate pipe into the corresponding rubber grommet. Install the Banks intermediate pipe onto the factory 2-bolt intermediate pipe outlet using the factory hardware. See Figure 1. When tightening the

Related Content:

bosch vp44 service manual, show me a picture of the diagram of an exhaust system of a Toyota matrix, Torque Wrench Instruction Manual, Toyota Exhaust Parts Diagram

1990 Toyota Supra Factory Repair Manual

0

Filed Under (Toyota Manuals) by admin on 04-04-2012

download
REMOVAL AND INSTALLATION OF TRANSMISSION Removal of Transmission REMOVE NEGATIVE BATTERY CABLE CAUTION: Work must be started after approx. 20 se- conds or longer from the “LOCK” position and the nega- tive (-) terminal cable is disconnected from the battery. REMOVE CENTER CLUSTER FINISH PANEL REMOVE SHIFT LEVER FROM INSIDE OF VEHICLE RAISE VEHICLE AND DRAIN TRANSMISSION OIL NOTICE: Be sure the vehicle is securely supported. REMOVE PROPELLER SHAFT Remove the propeller shaft and insert SST into the extension housing. SST 09325-2001 0 (for W58 M/T) 09325-4001 0 (for R 1 54 MIT) DISCONNECT EXHAUST FRONT PlPE FROM TAIL PlPE (a) Remove the rubber hanger. (b) Disconnect the pipe at the front side of the converter. (R154 M/T) REMOVE EXHAUST FRONT PlPE (a) Disconnect the exhaust pipe bracket from the clutch housing. (b) Remove the nuts and exhaust pipe from the exhaust manifold. DISCONNECT SPEEDOMETER CABLE DISCONNECT BACK-UP LIGHT SWITCH CONNECTOR AND REAR SPEED SENSOR CONNECTOR (wl A.B.S.) MANUAL TRANSMISSION – Removal and Installation of Transmission MT-5 10. REMOVE CLUTCH RELEASE CYLINDER 11. REMOVE STARTER Remove the mounting bolts and lay the starter alongside the engine. 12. JACK UP TRANSMISSION SLIGHTLY Raise the transmission enough to remove the weight from the rear support. 13. REMOVE ENGINE REAR MOUNTING 14. REMOVE TRANSMISSION MOUNTING BOLTS AND FLYWHEEL HOUSING UNDER COVER 15.-1 (W58 M/T) REMOVE TRANSMISSION ASSEMBLY Pull out the transmission down and toward the rear. 15.-2 (R154 M/T) REMOVE TRANSMISSION ASSEMBLY WITH CLUTCH COVER AND DISC (a) Remove the two clutch housing covers. (b) Pull out the release fork through the left clutch housing hole. (c) Place the matchmarks on the clutch cover and flywheel. (d) Remove the clutch cover set bolts while turning the crankshaft pulley. HINT: Loosen each set bolt one turn at a time until spring tension is released. (e) Remove the clutch cover and disc from the flywheel, and fully move them toward the transmission. (f) Pull out the transmission with the clutch cover and disc.

2005-2006 TOYOTA 4RUNNR GRILLE GUARD INSTALLATION INSTRUCTION

0

Filed Under (Toyota Manuals) by admin on 03-04-2012

download
Please read this installation Menu before installing this part. When install it, pay attention to protecting your vehicles. PART LIST ? When use it, please check this parts at a fix time – lapse, such as one month or two month. No. Name Qty Remarks No. Name Qty Remarks ?1 Grille guard 1 ?9 Hex bolt 2 M10 × 35 ?2 Left bracket 1 ? 10 Flat washer 4 10mm ?3 Right bracket 1 ? 11 Hex nut 2 M10 ?4 Left connecting plate 1 ? 12 Hex bolt 2 M12 × 40 ?5 Right connecting plate 1 ? 13 Hex bolt 2 M12 × 35 × 1.25 ?6 Hex bolt 4 M8 × 110 ? 14 Flat washer 6 12mm ?7 Flat washer 8 8mm ? 15 Spring washer4 12mm ?8 Hex nut 4 M8 INSTALLATION STEPS ? 10 ? 11 ? 12 ? 13 ? 14 ? 15 ?1 ?2 ?3 ?4 ?5 ?6 ?7 ?8 ?9 STEP ONE : Before you start the installation, make sure that you have all the components listed above. STEP TWO : Please protect your vehicles from being scratched during the process of installing the grille guard. INSTALLATION INSTRUCTION GRILLE GUARD FOR TOYOTA 4RUNNR 05-06 PART No. 82501.20/82001.20 Page 2 of 2 STEP THREE : Determine left connecting plate ,right connecting, left bracket and right bracket. STEP FOUR : Install grille guard to the vehicle with hardware listed as shown in Fig ?9? 10 ? 11 ?6?7?8 ? 5 ?1 ?6?7?8 ?2 ?3 ? 4 ? 12 ? 14 ? 15 ? 12 ? 14 ? 15 ? 13 ? 14 ? 15 ?9? 10 ? 11 ? 13 ? 14 ? 15 Fig

2000-2004 Toyota Tundra 4.7L V-8 Two and Four Wheel Drive Installation Manual

0

Filed Under (Toyota Manuals) by admin on 27-03-2012

download
1. Place vehicle in a location where the floor is solid and flat, with adequate lighting. Do not attempt to work on a hot engine. Heat causes metal to expand and makes removal of fasteners difficult at best. Disconnect the battery cables from the battery. Raise the front of the vehicle to obtain adequate access to the bottom exhaust manifold flanges. Use large-base jack stands to support the vehicle. Do not rely on the jack! Block the tires to prevent the vehicle from rolling off the jack stands. 2. Spray WD-40 or some type of penetrating oil on all accessible fasteners and fittings before attempting to remove them. 3. From underneath the vehicle disconnect the exhaust system from the exhaust manifolds by unbolting the (3) bolts at the collectors. Then unbolt the driver side catalytic converter from the exhaust assembly and temporarily remove it from the vehicle. PASSENGER SIDE 4. On the passenger side remove the (4) bolts attaching the heat shields to the factory manifold. 5. Next, carefully unplug the O2 sensor from its harness. 6. Now remove the nuts attaching the factory manifold to the cylinder head. With the manifold out of the way remove the mounting studs from the cylinder head. 7. Using a small wire brush or similar instrument, clean any carbon deposits left on the head surface. Be careful not to gouge the aluminum head. 8. Transfer the O 2 sensor from the factory manifold to the new passenger side header. Apply a small amount of anti seize to the threads for the sensor before installing it in the new header. Use caution not to drop or damage the sensor, they are fragile. 9. Now you are going to install the new JBA Header, but first there is some preparation of the hardware required. Apply anti seize to the threads of the new fasteners. Install the new JBA Header using the supplied gasket and fasteners. Torque to 23 ft./lbs. DRIVER’S SIDE 10. Just like you did in step (4) remove the (4) bolts attaching the heat shields to the driver side factory mani- fold. 11. Next, carefully unplug the O2 sensor from its harness. Unbolt the dipstick bracket from the head and remove the dipstick tube. 12. Remove the nuts attaching the factory manifold to the cylinder head. With the manifold out of the way remove the mounting studs from the cylinder head. 13. Using a small wire brush or similar instrument, clean any carbon deposits left on the head surface. Be careful not to gouge the aluminum head. 14. Transfer the O 2 sensor from the factory manifold to the new driver side header. Apply a small amount of anti seize to the threads for the sensor before installing it in the new header. Use caution not to drop or damage the sensor, they are fragile. 15. As you did on the passenger side, prepare the hardware before installing the driver side header. Apply anti seize to the threads of the new fasteners. Install the new JBA Header using the supplied gasket and fasteners. Torque to 23 ft./lbs. Re-install the dipstick tube. 16. Install the driver side catalytic converter. 17. Connect the exhaust system to the new headers using hardware and gaskets supplied. Reconnect O2 sensors. 18. Check to insure adequate clearance between header and shifter cable (small cable that runs from firewall, to brace on fender well, to transmission) . More clearance can be gained by adjusting (bending) brace on fender well. 19. Recheck everything

Related Content:

2004 honda civic head bolt torque, 4y toyota head torque

TOYOTA PRIUS FOG LIGHT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 18-03-2012

download
Remove the negative battery terminal Installation 1. Secure the relay to the next to the fuse block with wire ties 2. Attach the ring terminal with 2 black wires to ground 3. Attach fog light 12v red wire to open spade inside the fuse block as shown in picture 1 Picture 1 4. Locate the large vehicle harness grommet on the left side. Cut the auxiliary wiring access nipple off the grommet and push small 2-wire connector through firewall. Note: Extra caution should be taken not to damage connector 5. Run wires along the driver side of the engine compartment. Secure with wire ties as needed 6. From inside the cabin remove dash panels and locate the little small connector that was pushed through in step 4. Plug it to the switch harness. 7. T-tap orange/black wire from fog light harness to connector 2C pin 32 green wire. Pin 32 is on the left side of the connector 7th pin up from bottom of the connector. Connector 2C located left of the steering column above big white wire picture 2 Picture 2 8. T-Tap green/black wire from fog light harness to connector L47 pin 11, pink wire (it is the last pin to the left). Connector L47 is on the steering column and plugs into the headlight control arm picture 3 Picture 3 9. Mount switch into switch knockout of dash (picture 4) FOG LIGHT KIT INSTALLATION INSTRUCTIONS TPR-301 TOYOTA PRIUS 2010+ Picture 4 10. Install switch harness 11. Reinstall dash panels 12. Route the fog light wire under car. 13. Remove fog light cover plates and lower splash shields 14. Mount fog lights into bezel by sliding fog light tabs into slots and secure other side with supplied screw (see picture 5) Picture 5 15. Install both fog light bezels 16. Plug in left side fog light into harness plug 17. Run right fog light wire harness and plug into right fog light. Secure with wire ties 18. Reattach the lower splash shields

Related Content:

installing fog lights in 2012 sienna, how to connect fj cruiser corner fog lights, how to replace fog light on 2010 corolla youtube, 2010 corolla fog lamp installation, install instructions for fog lights on 2014 tacoma, install fog light 2013 sienna, install camry 2004 fog lights, how to replace fog light on 2010 corolla, how to install replacement fog lights in toyota rav 4 2014, how to install fog lights on a 2007 camry

Related Content:

pto connection on 2002 f450, kia transmission fuild temperture sensor, ford 555b engine oil capacity, park pin in a 4l60e transmission, mercury cougar beeping noise in idle, kia sedona 2004 repair manual pdf torrent, kia p0750 p0755 p0765, kancil manifold supply air inlet, instructions on radio for 2004 kia sorento, 1986 190e 2 3 throttle linkage adjustment